This template is used to generate an image map, showing the members of an association football squad on a football pitch. The position names and locations are specified per . The template does not check to make sure there are the correct number of players on the field.

Usage

{{football squad on pitch
| GK_nat  = | GK  =
| RB_nat  = | RB  =
| RCB_nat = | RCB =
| LCB_nat = | LCB =
| LB_nat  = | LB  =
| RCM_nat = | RCM =
| LCM_nat = | LCM =
| SS_nat  = | SS  =
| RW_nat  = | RW  =
| LW_nat  = | LW  =
| CF_nat  = | CF  =
}}

{{football squad on pitch
| GK_nat  = | GK  =
| RB_nat  = | RB  =
| RCB_nat = | RCB =
| LCB_nat = | LCB =
| LB_nat  = | LB  =
| RCM_nat = | RCM =
| LCM_nat = | LCM =
| AM_nat  = | AM  =
| RW_nat  = | RW  =
| LW_nat  = | LW  =
| CF_nat  = | CF  =
}}

{{football squad on pitch
| GK_nat  = | GK  =
| RB_nat  = | RB  =
| RCB_nat = | RCB =
| LCB_nat = | LCB =
| LB_nat  = | LB  =
| RCM_nat = | RCM =
| LCM_nat = | LCM =
| AM_nat  = | AM  =
| RM_nat  = | RM  =
| LM_nat  = | LM  =
| CF_nat  = | CF  =
}}

{{football squad on pitch
| GK_nat  = | GK  =
| RB_nat  = | RB  =
| RCB_nat = | RCB =
| LCB_nat = | LCB =
| LB_nat  = | LB  =
| RCM_nat = | RCM =
| LCM_nat = | LCM =
| RW_nat  = | RW  =
| LW_nat  = | LW  =
| RCF_nat = | RCF =
| LCF_nat = | LCF =
}}

{{football squad on pitch|image=striped
| GK_nat  = | GK  =
| RB_nat  = | RB  =
| RCB_nat = | RCB =
| LCB_nat = | LCB =
| LB_nat  = | LB  =
| RCM_nat = | RCM =
| LCM_nat = | LCM =
| RW_nat  = | RW  =
| LW_nat  = | LW  =
| RCF_nat = | RCF =
| LCF_nat = | LCF =
}}

Flags

The XX_nat parameters may be used to add national flags for the players. The ISO country code must be supported by {{ flagicon }} .

Alignment and width

By default, the diagram will float to the center of the page or column. To float the diagram to the left, use | align = left . To float the diagram to the right, use | align = right .

By default, the diagram width is set to 200px. To change the width, use | width = NUM , where NUM is a raw number, without the px units.

Long labels

If the label is too long, and is being clipped on the left or right edge of the diagram, try shifting it using | POS_shift = num , where POS is the position and num is a raw number in em units. This feature is currently only enabled for positions near the left and right edge of the diagram.

Caption

To add a caption, use | caption = .

Background image

To use a striped image, instead of the default checked image, use | image = striped .

See also